Do you own a 2001, 2002, 2003, 2004 or 2005 Toyota Rav4?
Are you having problems with the automatic transmission? The transmission acts erratically? Loss of power when accelerating or launching in other than first gear? Engaging very harsh in reverse? Slipping from 2nd to 3rd gear?
All those are problems caused by a defective ECM or Engine Control Module, a.k.a “Car Computer”.
The good news is that we have a solution for getting rid of the problem for good.
We are offering a REPAIR AND RETURN service for your Toyota Rav4 ECM (ECU). You send us your defective ECM, we repair and reprogram it and then it is shipped back to you. Our turn around time is one business day for most of the times or 2 business days when the workload is high. International orders are welcome too.
We offer FREE return shipping through USPS Priority Mail to continental USA, Puerto Rico, Hawaii, Alaska, Guam, American Samoa and US Virgin Islands. For international locations, return shipping cost will be calculated for FedEx shipping service. Return shipment to Canada can be served by USPS too, but unfortunately, we have no free options for it. We recommend FedEx for Canada though.
This is affecting more than a million units all around the world. It is so common that Toyota issued an “enhanced warranty” on this, which is long expired now.
This service covers 4WD Rav4 and 2WD Rav4 automatic vehicles. It also covers the Toyota Picnic and Toyota Avensis models of the same years (2001-2005).
We always stand by our customers. For our warranty on this service, please check the “Warranty” tab on this page.
Did you already service your ECM with any other shop or Company and they could not fix it? or, did you try fixing it yourself following any video and realized that it does not work? No worries, we accept those units too. ECMs that have been serviced previously by other shops or units attempted to be repaired by yourself, may take a little more time because in some cases, we need to fix additional problems induced by any previous repair attempt, but we will gladly accept your unit and do our best to help.
Wouldn’t it be better if the ECM is replaced by a new one?
New or used (recycled) ECMs are giving the same problems, some in the long run and others in a few months. Also, the repair cost of the ECM is much less than the cost of a brand new replacement ECM. We offer the most complete service on these units, as we cover the whole unit, not just the transmission problem and not just the symptom of the problem, but the cause of the problem too.
The following are the most common symptoms of this issue with the ECM:
- Check engine is not triggered in most cases
- When Check engine is triggered, it commonly shows P0750, P0753, P0755, P0758 and/or P1760 trouble codes when scanned
- Hesitation or harsh shifting, mostly from 2nd to 3rd gears
- Slams into gear when putting it in reverse
- Sometimes it feels like braking by itself
- Erratically shifts on an intermittent interval
- Rattling or clicking noise coming from the engine bay when the engine is running, even if in neutral gear
- Some days fails and some days works with no issues
- The problem is there only when the engine gets warm or only when it is started the first time in the morning
- When stopping completely and moving again, it loses power and feels sluggish or heavy
- Lower fuel economy. Spends more gas than usual
ECM Part Numbers
This is a partial list of the ECM part numbers affected. You will find the part number on the label at the top of your ECM. It starts with “89661”. Not all numbers are covered here, so if you don’t see your ECM number in the table below or if you are in doubt if your ECM is part of that list, please feel free to contact us to ask.
Removing the ECM from your vehicle:
Tools you will need:
- Short #2 Phillips screwdriver (stubby)
- Regular #2 Phillips screwdriver
- 10MM Socket Wrench
The kick panel and the scuff plate should be removed first, before starting the ECM removal procedure (check the first drawing below).
Now, proceed to:
1. Open the glove compartment box. There are two plastic pins, limiting its opening, one on each side at the inner end of the box. Push the two inner edges inwards, so the glove box gets disengaged from its place.
2. Now, with the regular Phillips screwdriver, remove the two screws in the lower part, that are holding the glove box to the dash.
3. With the glove box completely out, find the ECM computer at the right, which is a metallic box with 5 wiring connectors on it. It is near a smaller metallic box.
4. Unplug the 5 white wiring connectors one by one, by pushing on a locking plastic clip that each connector have while pulling the harness out at the same time.
5. With the 10mm socket wrench, remove the 10mm head bolt that attaches the ECM to the bracket at the lower part (refer to the second drawing below) and with the short Phillips screwdriver, remove the two screws at the top.
You might need a flashlight here to easily find those two upper screws and you might also need to move away any wiring away that might be in the path for taking the ECM out.
6. When the ECM is loose, carefully slide it downwards. It will come out with the rear bracket attached to it, so when it is out, remove the four Phillips screws as shown in the second picture below.
That’s it. You may pack it in a small box and send it to us!
If you have questions about this service, or the warranty we offer, or about shipment or if you need assistance, please feel free to contact us any time through the contact form on this page. We will be more than glad to help.
Searches: 2001 rav4 ecm repair, ecm rav4, 2001 toyota rav4 ecm repair, 2002 toyota rav4 ecm repair, 2002 toyota rav4 ecm recall, 2003 toyota rav4 ecm repair, 2003 toyota rav4 ecu, 2003 toyota rav4 transmission control module, toyota rav4 computer, toyota rav4 ecu repair, toyota rav4 ecm problemsWhat other users are looking for:
[89661-42702 ECU pin out] [How much ti fix the ecu in a 2001 toyota Rav4] [localisation circuit eprom calculateur moteur 2az highlander]