Comments on: 1993-1995 Accord – Prelude Performance Chip Installation

By: alex

alex — Fri, 04 Nov 2011 10:40:38 +0000

no i dont have the original one wat should i do know

By: Richard

Richard — Tue, 01 Nov 2011 00:31:31 +0000

Hello Alex.

The P0H ecu computer is for the 1994-1995 Honda Accord EX 2.2L.

May be the chip was not done for that P0H ecu. Chips must match the ecu, otherwise it will have some problems because sensors might be in different memory locations or even maps might be in other memory locations too.

Sometimes the ecu is just not 100% compatible with your car or application, coming form a car model different than yours.

Do you still have the original chip that was replaced (M38256)? If yes, what are the ID numbers on it? It should be two digits in big print, may be “G5″?

By: alex

alex — Mon, 31 Oct 2011 08:16:11 +0000

i have poh ecu dont know wat it came out of but it fets my 93 prelude the computer is chip so i bought a spoon chip but it don work right need help

By: Richard

Richard — Sun, 09 May 2010 23:23:24 +0000

Hello Chad.

Have you tried putting pack the stock chip on the modified P14? If you do and it comes back to normal, then the problem is in the chip, it is either not compatible or damaged.

If it was professionally installed, I guess that they gave you back the stock chip they took out and also a socket was installed, so the chip can be pulled out and replaced.

The ecu is now on a protection mode called “limp home” mode. The ecu assumes that mode to protect the engine when a problem with the chip or circuit is found. You will notice the check engine light on, not revving more than 3300-4000 RPMs and a very rich fuel mixture.

Just let me know.

Regards,

Richard

By: chad kennedy

chad kennedy — Sat, 08 May 2010 20:20:51 +0000

help me i bought a spoon chip and it dont work in my p14

By: chad kennedy

chad kennedy — Sat, 08 May 2010 20:19:56 +0000

i bought a spoon chip as well had it professionaly installed and now my car wont rev over 3000 rpms and sputters like crazy can u help me out i was smart i bought a 2nd p14 so my car is back up and running

By: admin

admin — Sat, 23 May 2009 02:01:34 +0000

Hello Efrain.

Do you still have the original chip? If you do, test the ecu with it. If everything works ok, then as you will guess the “Spoon” chip is the problem.

If it keeps the same with the stock (original) chip, then something happened to the ecu circuit when the installation was performed. In that case, it must be checked for loose or bad connections, broken traces on the board (either at the bottom and the top of the board) or soldering jumping one or more points.

If the Spoon chip is the problem, do not worry. Our chips are modified from the original, so you will get the extra power without disturbing the original functions of the ecu. If it doesn’t work well with ours, you can be sure that something happened to the ecu.

When your chip arrives, please check the instructions so you notice the orientation of the chip, since if it is installed backwards it may harm the ecu and / or the chip.

If still have problems when installing our chip, don’t worry, help is always available. Just contact us for further assistance. If at the end, the problem is the ecu, we can take a look at it to see if we can fix it.

Cheers,

Richard

By: efrain

efrain — Fri, 22 May 2009 17:41:11 +0000

hi? i bought the spoon chip i took it to a professional and i got it back and i install it and the car is not running right. its sounds like the fuel relay is tweeking off and on. the car was runnin good with out the cpu and once i put in the spoon chip is starting to mess up. please help, oooh i just bought your chip tooo see if your chip will work. help me. so everytime i start the car there is a clicking sound inside the car, its sounds like is the fuel pump relay..